4-20 mA Current Output Transmitter for AC Phase Angle & Power Factor

Transmits phase angle and power factor of AC waveforms. DIN Rail mounted, digitally programmable.

Navigation: Home > 4-20 mA transmitters

4-20 mA Current Transmitter, Phase Angle Input

Key Features

Isolated 4-20 mA or 0-10V transmitter outputs, selectable
Transmits phase angle between two AC wave shapes of similar period
Transmits power factor from 1.000 to 0.000 with sinusoidal signals
Frequency from 0.005 Hz to 10 kHz
Phase angle resolution of 1° , 0.1° or 0.01°
Phase angle accuracy of 0.01% at AC line frequency

Phase Angle Mode
Item Transmitted Transmitted Units Frequency Range Accuracy Maximum Timing Interval	Phase angle difference between two waves of same period 1°, 0.1°, 0.01° .005 Hz to 10 kHz .01°, .005 Hz to 100 Hz, 0.1° at 1 kHz, 1° at 10 kHz 200 s
Power Factor Mode
Item Transmitted Transmitted Units Polarity Frequency Range Accuracy	Power factor between two sine waves of same period 1.000 to 0.000, 1.00 to 0.00, or 1.0 to 1.0 Negative sign indicates negative phase angle 0.005 Hz to 10 kHz 0.1% at power line frequencies
Analog Output
Output Levels Compliance, 4-20 mA Compliance, 0-10V Output Resolution Output Accuracy Output Isolation	0-20 mA or 0-10 Vdc (selectable) 10V ( 0-500 ohm load ) 2 mA ( 5 kOhm load ) 16 bits (65,536 steps) 0.02% of output span plus conversion accuracy 250V rms working, 2.3 kV rms per 1 minute test
Inputs
Types Signal ground Minimum Signal Maximum Signal Noise Filter Contact Debounce	AC, pulses from NPN, PNP transistors, contact closures, magnetic pickups. Common ground for channels A & B Nine ranges from (-12 to +12 mV) to (+1.25 to +2.1V) 250 Vac 1 MHz, 30 kHz, 250 Hz (selectable) 0, 3, 50 ms (selectable)
Update Rate
Conversion Interval Gate Time Time Before Zero Output	Gate time + 30 ms + 0-2 signal periods Selectable 10 ms to 199.99 s Selectable 10 ms to 199.99 s
Sensor Excitation Output (standard)
Output Levels Output Isolation	5V@100 mA, 10V@120 mA, 24V@50 mA (jumper selectable) 50V from signal ground
Dual Relay Output (standard)
Relay Type Load Rating	Two solid state relays, SPST, normally open, Form A 130 mA at 140 Vac or 180 Vdc
Serial Communications (standard)
Signal Types Data Rates Output Isolation Serial Protocols Modbus Modes Modbus Compliance Digital Addressing	RS232 or RS485 (half or full duplex) 300, 600, 1200, 2400, 4800, 9600, 19200 baud 250V rms working, 2.3 kV rms per 1 min test Modbus RTU, Modbus ASCII, Laurel ASCII RTU or ASCII Modbus over Serial Line Specification V1.0 (2002) 247 Modbus addresses. Up to 32 devices on an RS485 line w/o a repeater.
Power Input
Standard Power Low Power Option Power Frequency Power Isolation Power Consumption	85-264 Vac or 90-300 Vdc (DC operation not UL approved) 10-48 Vdc or 12-32 Vac DC or 47-63 Hz 250V rms working, 2.3 kV rms per 1 min test 2W typical, 3W with max excitation output
Mechanical
Dimensions Mounting Electrical Connections	129 x 104 x 22.5 mm case 35 mm rail per DIN EN 50022 Plug-in screw-clamp connectors
Environmental
Operating Temperature Storage Temperature Relative Humidity Cooling Required	0°C to 55°C -40°C to 85°C 95% at 40°C, non-condensing Mount transmitters with ventilation holes at top and bottom. Leave 6 mm (1/4") between transmitters, or force air with a fan.