4-20 mA Current Output Transmitter for Strain Gauge & Potentiometer Input

Ideal for load & pressure. DIN Rail mounted, digitally programmable. Scalable for strain gauge and potentiometer follower signals.

Navigation: Home > Transmitters, 4-20 mA

Key Features

200 mV, 2V, 20V, 200V & 300V input ranges
All ranges factory calibrated
Digital span adjust from 0 to ±99,999 internal counts
Digital zero adjust from -99,999 to +99,999 internal counts
Digital zero adjust from -99,999 to +99,999
Output resolution: 0.0015% of span (16 bits)
10V, 120 mA excitation output to power four 350 ohm load cells in parallel, isolated
4-20 mA, 0-20 mA or 0-10V transmitter output, jumper selectable, isolated
Output accuracy: ±0.02% of span
Output update rate to 60/sec
Switching supply for 85-264 Vac

Specifications

Laureate 4-20 mA Transmitter for Strain Gauge or Potentiometer Follower Input

Analog Input	Range	Resolution	Accuracy	Input Ohms
DC Voltage	200.00 mV 2.0000 V 20.000 V 200.00 V 600.0 V	10 µV 100 µV 1 mV 10 mV 100 mV	±0.01% FS ± 2 counts	1 GΩ 1 MΩ 1 MΩ 1 MΩ 1 MΩ
DC Current	2.0000 mA 20.000 mA 200.00 mA	0.1 µA 1 µA 10 µA	±0.01% FS ± 2 counts	100 Ω 10 Ω 1 Ω
	5.000 A	1 mA	±0.1% FS ± 2 counts	0.01 Ω
Input Resolution Update Rate, Max Max applied voltage Over-current protection	16 bits (65,536 steps) 50/sec at 50 Hz, 60/sec at 60 Hz 600 Vac for 20, 200 & 600 V ranges, 125 Vac other ranges 25x for 2 mA, 8x for 20 mA, 2.5x for 200 mA, 1x for 5 A
Analog Output
Output Levels Compliance, 4-20 mA Compliance, 0-10V Output Resolution Output Accuracy Output Isolation	0-20 mA or 0-10 Vdc (selectable) 10V ( 0-500Ω load ) 2 mA ( 5 kΩ load ) 16 bits (65,536 steps) 0.02% of output span plus conversion accuracy 250V rms working, 2.3 kV rms per 1 minute test
Dual Relay Output (standard)
Relay Type Load Rating	Two solid state relays, SPST, normally open, Form A 130 mA at 140 Vac or 180 Vdc
Transducer Excitation Output (standard)
Output Levels Output Isolation	5V@100 mA, 10V@120 mA, 24V@50 mA (jumper selectable) 50V from signal ground
Serial Data Output (standard)
Signal Types Data Rates Output Isolation Serial Protocols Modbus Modes Modbus Compliance Digital Addressing	RS232 or RS485 (half or full duplex) 300, 600, 1200, 2400, 4800, 9600, 19200 baud 250V rms working, 2.3 kV rms per 1 min test Modbus RTU, Modbus ASCII, Laurel ASCII RTU or ASCII Modbus over Serial Line Specification V1.0 (2002) 247 Modbus addresses. Up to 32 devices on an RS485 line w/o a repeater.
Power Input
Standard Power Low Power Option Power Frequency Power Isolation Power Consumption	85-264 Vac or 90-300 Vdc (DC operation not UL approved) 10-48 Vdc or 12-32 Vac DC or 47-63 Hz 250V rms working, 2.3 kV rms per 1 min test 2W typical, 3W with max excitation output
Mechanical
Dimensions Mounting Electrical Connections	129 x 104 x 22.5 mm case 35 mm rail per DIN EN 50022 Plug-in screw-clamp connectors
Environmental
Operating Temperature Storage Temperature Relative Humidity Cooling Required	0°C to 55°C -40°C to 85°C 95% at 40°C, non-condensing Mount transmitters with ventilation holes at top and bottom. Leave 6 mm (1/4") between transmitters, or force air with a fan.