Modbus & Serial Output Transmitter for AC RMS Voltage or Current Input

AC RMS Input	Range	Resolution	Input Ohms	Error at 25°C
Voltage Ranges 0% to 100% of FS, 10 Hz to 10 kHz	200.00 mV 2.0000 V 20.000 V 200.00 V	10 µV 100 µV 1 mV 10 mV	1 MΩ	± 0.1% of FS
	600.0 V	100 mV	1 MΩ	± 0.3% of FS
Current Ranges 0% to 100% of FS, 10 Hz to 10 kHz	2.0000 mA 20.000 mA 200.00 mA	0.1 µA 1 µA 10 µA	100 Ω 10 Ω 1 Ω	± 0.1% of FS
	5.000 A	1 mA	0.01 Ω	± 0.4% of FS
Input Resolution A/D Conversion Ratae Max applied voltage Over-current protection AC RMS Crest Factor	16 bits (65,536 steps) 50/sec at 50 Hz power, 60/sec at 60 Hz power 600 Vac for 20, 200, 600V ranges, 50 Vac other anges 25x for 2 mA, 8x for 20 mA, 2.5x for 200 mA, 1x for 5A 3.0x at 100% of full scale
Analog Output (standard)
Output Levels Compliance, 4-20 mA Compliance, 0-10V Output Resolution Output Accuracy Output Isolation Update Rate, > 50/60 Hz Update Rate, 3 to 50/60 Hz Update Rate, DC to 3 Hz	4-20 mA, 0-20 mA, 0-10 Vdc (jumper selectable) 10V ( 0-500Ω load ) 2 mA ( 5 kΩ load or higher) 16 bits (65,536 steps) 0.02% of output span plus conversion accuracy 250V rms working, 2.3 kV rms per 1 minute test 60/s at 60 Hz power, 50/s at 50 Hz power One signal cycle Every 3.333 ms
Dual Relay Output (standard)
Relay Type Load Rating	Two solid state relays, SPST, normally open, Form A 130 mA at 140 Vac or 180 Vdc
Serial Communications (standard)
Signal Types Data Rates Output Isolation Serial Protocols Modbus Modes Modbus Compliance Digital Addressing	RS232 or RS485 (half or full duplex) 300, 600, 1200, 2400, 4800, 9600, 19200 baud 250V rms working, 2.3 kV rms per 1 min test Modbus RTU, Modbus ASCII, Laurel ASCII RTU or ASCII Modbus over Serial Line Specification V1.0 (2002) 247 Modbus addresses. Up to 32 devices on an RS485 line w/o a repeater.
Power Input
Standard Power Low Power Option Power Frequency Power Isolation Power Consumption	85-264 Vac or 90-300 Vdc (DC operation not UL approved) 10-48 Vdc or 12-32 Vac DC or 47-63 Hz 250V rms working, 2.3 kV rms per 1 min test 2 W
Mechanical
Dimensions Mounting Electrical Connections	129 x 104 x 22.5 mm case 35 mm rail per DIN EN 50022 Plug-in screw-clamp connectors
Environmental
Operating Temperature Storage Temperature Relative Humidity Cooling Requirement	0°C to 55°C -40°C to 85°C 95% at 40°C, non-condensing Leave 6 mm (1/4") between transmitters, or force air with a fan.