Modbus & Serial Output Transmitter for Duty Cycle Input

Transmits ON or OFF period in percent of total period. DIN Rail mounted, digitally programmable.

Navigation: Home > Transmitters-modbus

Serial ASCII or Modbus Transmitter, Duty Cycle Input

Key Features

Selectable Modbus or Laurel ASCII protocol
Modbus RTU or ASCII modes, 2-wire connection, up to 247 digital addresses
Transmits ON or OFF period as a percentage of total period
Resolution of 1%, 0.1% or 0.01%
Frequencies from .005 Hz to 10 kHz
Triggers on positive or negative pulse edges
Optional dual solid state relays for alarm or control
5V, 10V or 24V dc sensor excitation output, isolated
Dual solid state relays for alarm or control, isolated
Dual solid state relays for alarm or control, isolated
0-10V, 4-20 mA or 0-20 mA transmitter output, isolated
Universal AC power, 85-264 Vac

Laureate Modbus & Serial Output Transmitter for Duty Cycle Input

Pulse Input
Types Signal Ground Minimum Signal Maximum Signal Maximum Frequency Contact Debounce	AC, pulses from NPN, PNP transistors, contact closures, magnetic pickups. Common ground for channels A & B Nine ranges from (-12 to +12 mV) to (+1.25 to +2.1V) 250 Vac 1 MHz, 30 kHz, 250 Hz (selectable) 0, 3, 50 ms (selectable)
Duty Cycle Mode
Item Displayed Display Units Frequency Range Input Accuracy Maximum Timing Interval	ON or OFF duty cycle of periodic pulse waveshape 1%, 0.1%, 0.01% 0.005 Hz to 50 kHz 0.01%, 0.005 Hz to 500 Hz, 0.1% at 5 kHz, 1% at 50 kHz 199.99 s
Update Rate
Conversion Interval Gate Time Time Before Zero Output	Gate time + 30 ms + 0-2 signal periods Selectable 10 ms to 199.99 s Selectable 10 ms to 199.99 s
Serial Data I/O (standard)
Signal levels Data Rates Output Isolation Serial Protocols Devices on RS-485 Line Modbus Addresses Modbus Modes Modbus Compliance	RS232 or RS485 (half duplex) 300, 600, 1200, 2400, 4800, 9600, 19200 baud 250V rms working, 2.3 kV rms per 1 min test Modbus RTU, Modbus ASCII, Laurel ASCII (selectable) 32 max without a repeater. 247 max RTU or ASCII, 2-wire. Modbus over Serial Line Specification V1.0 (2002).
Transducer Excitation Output (standard)
Output Levels Output Isolation	5V@100 mA, 10 @120 mA, 24V@50 mA (jumper selectable) 50V from signal ground
Dual Relay Output (standard)
Relay Type Load Rating	Two solid state relays, SPST, normally open, Form A 130 mA at 140 Vac or 180 Vdc
Analog Output (standard)
Output Levels Compliance, 4-20 mA Compliance, 0-10V Output Resolution Output Accuracy Output Isolation	4-20 mA, 0-20 mA, 0-10 Vdc (jumper selectable) 10V ( 0-500 ohm load ) 2 mA ( 5 kOhm load or higher) 16 bits (65,536 steps) 0.02% of output span plus conversion accuracy 250V rms working, 2.3 kV rms per 1 minute test
Power Input
Standard Power Low Power Option Power Frequency Power Isolation Power Consumption	85-264 Vac or 90-300 Vdc (DC operation not UL approved) 10-48 Vdc or 12-32 Vac DC or 47-63 Hz 250V rms working, 2.3 kV rms per 1 min test 2W typical, 3W with max excitation output
Mechanical
Dimensions Mounting Electrical Connections	129 x 104 x 22.5 mm case 35 mm rail per DIN EN 50022 Plug-in screw-clamp connectors
Environmental
Operating Temperature Storage Temperature Relative Humidity Cooling Required	0°C to 55°C -40°C to 85°C 95% at 40°C, non-condensing Mount transmitters with ventilation holes at top and bottom. Leave 6 mm (1/4") between transmitters, or force air with a fan.