Modbus & Serial Output RTD Temperature Transmitter

RTD Metal	Alpha	R at 0°C	R at top of range	Excitation Current	Range	Conformity Error
Platinum	0.003850 (DIN)	100Ω	390.48Ω at 850°C	196 µA	-200°C to +850°C -328°F to +1562°F	±0.03°C ±0.05°F
Platinum	0.003902 (ANSI)	100Ω	394.36Ω at 850°C	196 µA	-200°C to +850°C -328°F to +1168°F	±0.04°C ±0.07°F
Nickel	0.00672	120Ω	380.31Ω at 850°C	196 µA	-80°C to +260°C -112°F to +500°F	±0.05°C ±0.09°F
Copper	0.00427	9.035Ω	19.116Ω at 850°C	5.0 mA	-97°C to +260°C -143°F to +500°F	±0.05°C ±0.09°F

 

RTD Input
Calibration, Pt 100 DIN Calibration, Pt 100 ANSI Configuration Excitation current Overall accuracy Span tempco Zero tempco Sensor lead resistance    tempco per conductor Over-voltage protection Open sensor indication	IEC 751 (IPTS-68) NIST Monograph 126 2, 3 or 4-wire connection 0.2 mA ±0.01 of full scale ±2 counts ±0.003% of reading/°C ±0.03 deg/deg 2-wire, 10 mdeg/Ω/deg up to 10Ω 3 & 4-wire, 10 mdeg/Ω/deg up to 100Ω 125 Vac 0 mA or > 20 mA output, selectable
Serial Data Output (standard)
Signal Types Data Rates Output Isolation Serial Protocols Modbus Modes Modbus Compliance Digital Addressing	RS232 or RS485 (half or full duplex) 300, 600, 1200, 2400, 4800, 9600, 19200 baud 250V rms working, 2.3 kV rms per 1 min test Modbus RTU, Modbus ASCII, Laurel ASCII RTU or ASCII Modbus over Serial Line Specification V1.0 (2002) 247 Modbus addresses. Up to 32 devices on an RS485 line w/o a repeater.
Analog Output (standard)
Output Levels Compliance, 4-20 mA Compliance, 0-10V Output Resolution Output Accuracy Output Isolation	4-20 mA, 0-20 mA, 0-10 Vdc (jumper selectable) 10V ( 0-500Ω load ) 2 mA ( 5 kΩ load or higher) 16 bits (65,536 steps) 0.02% of output span plus conversion accuracy 250V rms working, 2.3 kV rms per 1 minute test
Dual Relay Output (standard)
Relay Type Load Rating	Two solid state relays, SPST, normally open, Form A 130 mA at 140 Vac or 180 Vdc
Power Input
Standard Power Low Power Option Power Frequency Power Isolation Power Consumption	85-264 Vac or 90-300 Vdc (DC operation not UL approved) 10-48 Vdc or 12-32 Vac DC or 47-63 Hz 250V rms working, 2.3 kV rms per 1 min test 2W typical
Mechanical
Dimensions Mounting Electrical Connections	129 x 104 x 22.5 mm case 35 mm rail per DIN EN 50022 Plug-in screw-clamp connectors
Environmental
Operating Temperature Storage Temperature Relative Humidity Cooling Required	0°C to 55°C -40°C to 85°C 95% at 40°C, non-condensing Mount transmitters with ventilation holes at top and bottom. Leave 6 mm (1/4") between transmitters, or force air with a fan.